All about the pattern and sewing of a sarafan with buttons in the front

Sundresses with buttons in the front were extremely popular in the 50s and then in the 90s. Today, they are again among the top fashion trends. For sewing such models, thin suit fabrics are used, both natural and mixed. Such a sundress can be used as an everyday wardrobe item, evening or office. It is not difficult at all to sew it yourself, it is enough to have basic sewing skills.

Modeling a sarafan pattern

The main advantage of sarafans is the simplicity of modeling and sewing. Even a novice seamstress can cope with the task. If you know how to design a basic drawing-basis of a fitted dress with a straight skirt, you can design many different options from classic to elegant.

With a shuttlecock on his shoulders

To sew a sarafan with buttons in the front, the pattern is modeled very simply. First of all, it is necessary to measure the volume of the chest.

The length of the product is determined independently. Do not forget to leave allowances for seams. After taking measurements, you should cut out two rectangles, overcast the details and sew the product along the side edges on both sides.

You need to leave space for the armholes at the top. As a result of the above actions, you will get a blank in the form of a tube. Then, using an overlock, you need to process the armholes.

The next step is to cut out the frill. Measurements must be taken in a circle over the shoulders. The resulting result must be doubled and add 2 cm for allowances.

The flounce is sewn and hemmed on all sides. An elastic band is inserted into the upper part and, taking into account the armhole, it is sewn to the base of the dress. The material is cut in the front. Loops are made on one side, and buttons are sewn on the other.

With one-piece sleeves

A sundress with one-piece sleeves is a classic solution. This model looks impressive and can decorate a woman with any figure. The main nuance of this model is the absence of armholes.

To model a pattern for such a sundress, you need to take measurements, then draw a straight line on a sheet of paper equal to the distance from the waist of the garment to the hem. The darts need to be reduced and the armhole lengthened. Through the new marks, draw perpendiculars towards the cuts on the base. The shoulder cut line needs to be raised by 0.5 cm in front and by 0.7 cm in back. Set aside 7 cm from the end of the shoulder for the neckline.

On an elastic band

An open back on a sundress looks feminine and beautiful. Sewing such a sundress with buttons using a pattern modeled in advance will not be a problem. To construct the product, you need to construct a rectangle where its width will be equal to the hip circumference, and the length in each case is determined individually. As soon as the base of the sundress is ready, you can cut the product in the front and sew on buttons. The final stage is sewing on the elastic. This option is ideal for both little girls and young women.

Modeling a straight model from cotton

The model is the embodiment of beauty and femininity. Visually, such a model can make any woman slimmer. The pattern can be immediately drawn on the fabric.

First, you need to take measurements - chest, hips and waist. Mark the dots, connect them with a smooth line. The top can be made straight. Divide the front into two halves for buttons. As practice shows, the pattern of a sundress with straps and buttons is very simple and does not require certain knowledge and skills.

For full with smell

For plus size women, whose clothing size starts from size 52, wide, but not shapeless models with a V-neck are ideal.

It is recommended to take a dress as a basis and perform the following steps:

1. the top should be cut off at the waist line;
2. close the bust dart and widen the waist dart;
3. cut to the top of the closed chest and put a dot;
4. from the top point in the side cut, measure down 4 cm and from it to the right 1 cm, then draw a parallel line;
5. measure 13-15 cm from the center front line;
6. from the lower peak of the shoulder dart, measure 10 cm up and put a point, connect it with the one measured from the center line of the front and from the side cut;
7. from the upper side cut down measure 4 cm and 1 cm to the left, from this point draw a horizontal line to the middle line of the back and parallel downwards.

This completes the modeling of the summer sarafan pattern for plump women. In the Burda magazine you can find many varieties of modeling this model.

Sundress for the office

The drawing is developed on the basis of a quadrangle. The height of the chest, waist, hips is marked horizontally and a line is drawn. After this, the following actions are performed:

1. from one edge along the chest line, half the width of the back is measured;
2. on the other edge, half the value of the dart solution;
3. straight lines rise from the obtained points to the upper boundary of the rectangle at an angle of 90 degrees;
4. ¼ of the neck circumference measurement is set aside and the shoulder seams are drawn;
5. marks are raised along the front panel and a line is drawn for inserting buttons;
6. the armhole area is set aside and a perpendicular is lowered through its center to the lower border of the rectangle;
7. the difference between the chest and waist measurements is determined;
8. the value is distributed into side seams and darts;
9. measure ¼ of the hip measurement from the sides of the rectangle and draw a curved side seam.

For pregnant women

Constructing a pattern for a sundress with straps for pregnant women will also not cause any problems. Such models are designed for the changes that occur with a girl's figure while expecting a child.

The classic version consists of a base and straps. For the base, the length from the armpit to the knees or another length as desired is measured, as well as the waist circumference.

Such sarafans make life much easier for pregnant women. Their free cut and deepening for the stomach make the wearing process as comfortable as possible. The bodice is cut in such a way that it is easy to remove the breast for feeding the baby.

In boho style

To model the pattern, the chest width and the chest height are measured. The length and width of the straps are determined arbitrarily.

Floor length

The maxi length makes the sarafan a comfortable and elegant wardrobe item. The pattern of the sarafan on straps with buttons in the front is modeled in the same way as in the case of the classic version. The only difference is the length.

How to cut out a sundress with buttons in the front

To sew a buttoned sarafan, the pattern is modeled according to the basic dress pattern with an allowance for freedom of fit. The summer sarafan is buttoned in front. It is recommended to start modeling from the front half of the dress. Then the front half of the product is cut along the waist line and the bust dart is transferred to the waist dart.

How to sew a sundress with buttons

Once the model is selected and the pattern is modeled, it will be very easy to sew a buttoned sarafan with your own hands. First, the side panels are stitched, the cut lines where the buttons will be located are hemmed, as well as the top and bottom of the product. Loops are made, which after formation can be decorated with an awl. The final stage will be sewing on the buttons and decorative trim, which is done at will.

The decor options can be completely different. Here everything depends on personal preferences. On the sarafan you can do embroidery with colored threads, sew on stripes, rhinestones, decorative buttons or brooches.

Sundresses with buttons in the front are very popular among modern girls and women. Sewing such a wardrobe item with your own hands will not be difficult. Moreover, the pattern for this product is extremely simple. As for the fabric, it is best to make a sundress from natural material. The ideal option would be to use chintz, calico, silk, cotton or gauze. If you use viscose, wool or velveteen, then the product will be warm and suitable for the cold season.